Head Rod Molding (Awning Rail) 24'
Availability:
In stock
SKU
AWRAIL24
Please speak to your sales rep for large volume rates
Head Rod Molding (awning rail) is an aluminum extrusion is designed for use with a 1/2 inch diameter conventional head rod to eliminate the awkward job of threading a rope-filled hem through a slot in the molding. The head rod is merely placed in position and finger clips are tightened to hold the head of the awning under the rainproof lip of the molding. The finger clips ride in a track in the molding and can be adjusted to move laterally right or left.
For installations at the head of stationary or patio awnings and for installation and adjustment of the rafters of patio awnings. Extruded from 6063-T5 aluminum - mill finish.
Number 37 Head Rod Moldings are designed for use with a 1/2 inch diameter conventional head rod to eliminate the awkward job of threading a rope-filled hem through a slot in the molding. The head rod is merely placed in position and finger clips are tightened to hold the head of the awning under the rainproof lip of the molding. The finger clips ride in a track in the molding and can be adjusted to move laterally right or left.
The advantage of this system is that rafters can be placed precisely, even if the surface is uneven or the mounting supports are not located where the rafters should be, because once the molding is mounted, the rafters can be slid to their proper location.
Recommended rafter spacing is 1 1/2 feet in from each side, and then 3 feet to 4 feet centers depending on projection (the longer the rafters, the less the spacing). Awning rafters are attached to special jaw ends that are mounted in a track in the lower side of the molding. The jaw ends can be moved laterally to adjust the rafter width. This is done by turning or tightening the jaw end, which is fitted with a carriage bolt to ride in the same track as the finger clip.
The molding itself is designed so that a bead of caulking compound can be applied to the top length of the molding to prevent water from leaking behind the molding and down the wall.
The Number 37 molding has the same basic design as the No. 35 but hs more strength and is heavier duty. The No. 37 Finger Clip and No. 37W Jaw End can be used with the No. 35 Molding without alteration.
For installations at the head of stationary or patio awnings and for installation and adjustment of the rafters of patio awnings. Extruded from 6063-T5 aluminum - mill finish.
Number 37 Head Rod Moldings are designed for use with a 1/2 inch diameter conventional head rod to eliminate the awkward job of threading a rope-filled hem through a slot in the molding. The head rod is merely placed in position and finger clips are tightened to hold the head of the awning under the rainproof lip of the molding. The finger clips ride in a track in the molding and can be adjusted to move laterally right or left.
The advantage of this system is that rafters can be placed precisely, even if the surface is uneven or the mounting supports are not located where the rafters should be, because once the molding is mounted, the rafters can be slid to their proper location.
Recommended rafter spacing is 1 1/2 feet in from each side, and then 3 feet to 4 feet centers depending on projection (the longer the rafters, the less the spacing). Awning rafters are attached to special jaw ends that are mounted in a track in the lower side of the molding. The jaw ends can be moved laterally to adjust the rafter width. This is done by turning or tightening the jaw end, which is fitted with a carriage bolt to ride in the same track as the finger clip.
The molding itself is designed so that a bead of caulking compound can be applied to the top length of the molding to prevent water from leaking behind the molding and down the wall.
The Number 37 molding has the same basic design as the No. 35 but hs more strength and is heavier duty. The No. 37 Finger Clip and No. 37W Jaw End can be used with the No. 35 Molding without alteration.
Product Features:
- High Quality aluminum
- Perfect for residential awnings
- Use with Jaw End and finger clip for customized awnings.
| SKU | AWRAIL24 |
|---|---|
| Length | 24' |
| Sold Per | Unit |
| Alloy | 6063-T5 |
Write Your Own Review